Beta Marine Engines

Blue Moon · Blue Moon

Using both the Balmar instructions for the MC-614 regulator and some very helpful drawings, pictures, and advice from Farron, I installed the Balmar regulator, the Iskra brush box supplied by Beta, and triple-checked all wiring and connections. Nonetheless, there is a problem. At idle, my shunt...

Rowboatload · Rowboatload

I have a BZ482 with about 300 hours of use. Three days ago I was two hours into a 2,200 r.p.m motor against a gentle wind with my 27 ft. sailboat when the revs dropped to about 1000 and it would not go any higher. I ran it for about 10 minutes then turned it off and sailed back near my marina then restarted it a...

SClendenin · SClendenin

I have a Beta 20 hp. WOC is K20524 I see that prior to Dec 2005 there was a side mount available for the on engine fuel 5 micron filter. For some unknown, to me, reason the previous owner removed the on engine filter. I think it may have been due to a problem with the design of the companionway steps being too...

SkipD · SkipD

This is a 2019 installation in an Albin 27 with a Beta 50 w/TMC60 and Python-Drive, less than a 100 hours to date. Overall everything is working fine. Have always been sensitive to noise and have insulated & reinforced the boat to get the noise level down to 76db at 2000 rpm just above the engine com...

Johan W · Johan W

Hi, I have a 10 year old BD722, 20hp engine Installed in my sailing boat. The sea water pump is leaking water from the backside. I have ordered a new original spare part pump. My questions are, do I need any special tools to remove the old one and install the new one or is it just to loosen the two screws/clam...

Topic		Started By	Replies	Views	Last Post
	Trouble After Modifying Beta 38 w/ Iskra 120 A Alternator for External Balmar MC-614 Regulation (Preview) Using both the Balmar instructions for the MC-614 regulator and some very helpful drawings, pictures, and advice from Farron, I installed the Balmar regulator, the Iskra brush box supplied by Beta, and triple-checked all wiring and connections. Nonetheless, there is a problem. At idle, my shunt...	Blue Moon	3	1594	Aug 25, 2020 by Blue Moon
	BZ482 13.3 LAGGED - THEN RAN AWAY (Preview) I have a BZ482 with about 300 hours of use. Three days ago I was two hours into a 2,200 r.p.m motor against a gentle wind with my 27 ft. sailboat when the revs dropped to about 1000 and it would not go any higher. I ran it for about 10 minutes then turned it off and sailed back near my marina then restarted it a...	Rowboatload	2	860	Aug 23, 2020 by Rowboatload
	side mount fuel filter (Preview) I have a Beta 20 hp. WOC is K20524 I see that prior to Dec 2005 there was a side mount available for the on engine fuel 5 micron filter. For some unknown, to me, reason the previous owner removed the on engine filter. I think it may have been due to a problem with the design of the companionway steps being too...	SClendenin	0	920	Aug 19, 2020 by SClendenin
	TMC60- Clicking/Ticking Noise (Preview) This is a 2019 installation in an Albin 27 with a Beta 50 w/TMC60 and Python-Drive, less than a 100 hours to date. Overall everything is working fine. Have always been sensitive to noise and have insulated & reinforced the boat to get the noise level down to 76db at 2000 rpm just above the engine com...	SkipD	7	640	Aug 10, 2020 by Stanley
	Replacement of the sea water pump (Preview) Hi, I have a 10 year old BD722, 20hp engine Installed in my sailing boat. The sea water pump is leaking water from the backside. I have ordered a new original spare part pump. My questions are, do I need any special tools to remove the old one and install the new one or is it just to loosen the two screws/clam...	Johan W	1	677	Aug 6, 2020 by Stanley
«First < 1 … 15 16 17 18 19 … 147 > Last» \| Page of 147 sorted by