Beta Marine Engines

Blue Moon · Blue Moon

In replacing the heat exchanger anode for the first time last month on my one-season-old Beta 38, I noticed what appears to be some corrosion around the anode cap, apparently due to some slight weeping. The cap was quite tightly snugged down and there has never been any dripping or other obvious evide...

Rickiellen · Rickiellen

Im repowering a Falmouth Cutter 22 (sailboat) with very limited space in the engine compartment. Running proper exhaust hose with a loop at transom is a challenge. I see that Beta Marine sells a plastic gooseneck exhaust that looks like it would be just the trick for my boat, but my mechanic who is do...

Blue Moon · Blue Moon

My Beta 38 was newly installed in May 2017, so in only the one season through September 2017--perhaps twenty weeks and shortened last year by a family wedding. In that time, excepting the times were were running anywhere off the New England coast, the boat hung on moorings (a) way out near the mouth of R...

Blue Moon · Blue Moon

Thank you, Stan, for the coaching on removing my coupling and transmission from my Beta 38 as the least painful way to bring my prop shaft in enough to remove my problem cutlass bearing. Today I got the stage set, arranging access, supports, tools, and so on and so will attack the thing in the coming days...

firefly2014 · firefly2014

Drains fuel thru an open-ended clear flexible tube which runs from the right side of the engine (looking from the front) to below the sump that then drains into the bilge. What is this drain? I had a problem with engine quitting and found gallons of fuel in the bilge. Clogged fuel filter?? All the fuel le...

Topic		Started By	Replies	Views	Last Post
	Corrosion around anode cap on Beta 38 (Preview) In replacing the heat exchanger anode for the first time last month on my one-season-old Beta 38, I noticed what appears to be some corrosion around the anode cap, apparently due to some slight weeping. The cap was quite tightly snugged down and there has never been any dripping or other obvious evide...	Blue Moon	4	723	May 16, 2020 by NeilMcCubbin
	Plastic gooseneck exhaust (Preview) Im repowering a Falmouth Cutter 22 (sailboat) with very limited space in the engine compartment. Running proper exhaust hose with a loop at transom is a challenge. I see that Beta Marine sells a plastic gooseneck exhaust that looks like it would be just the trick for my boat, but my mechanic who is do...	Rickiellen	2	803	May 16, 2020 by NeilMcCubbin
	Quickly wasting anode on Beta 38 (Preview) My Beta 38 was newly installed in May 2017, so in only the one season through September 2017--perhaps twenty weeks and shortened last year by a family wedding. In that time, excepting the times were were running anywhere off the New England coast, the boat hung on moorings (a) way out near the mouth of R...	Blue Moon	6	812	May 16, 2020 by NeilMcCubbin
	Bolt Sizing on Transmission Mount Plate and R&D Coupling (Preview) Thank you, Stan, for the coaching on removing my coupling and transmission from my Beta 38 as the least painful way to bring my prop shaft in enough to remove my problem cutlass bearing. Today I got the stage set, arranging access, supports, tools, and so on and so will attack the thing in the coming days...	Blue Moon	1	965	May 16, 2020 by Blue Moon
	My Beta 25 is draining fuel (Preview) Drains fuel thru an open-ended clear flexible tube which runs from the right side of the engine (looking from the front) to below the sump that then drains into the bilge. What is this drain? I had a problem with engine quitting and found gallons of fuel in the bilge. Clogged fuel filter?? All the fuel le...	firefly2014	4	684	May 14, 2020 by firefly2014
«First < 1 … 19 20 21 22 23 … 148 > Last» \| Page of 148 sorted by