Beta Marine Engines

CapnB · CapnB

I want to install a tach in the ****pit of my Vancouver 32. The control panel is below near the nav station, but I want to be able to see the tach when in the ****pit - this set-up concept is left over from the original engine (a Bukh 20) and I liked the idea. Has anyone doen this? What is available from Beta for...

captleasure207 · captleasure207

Hi - I have a Beta 38 and the other day it raced to full RPMs at start up. I was able to get it to shut off with the engine panel stop button. I've removed the throttle cover and saw the rack pin on the injector pin was stuck. I was able to get it unstuck. I also removed the stop solenoid and the T shaped bar inside...

BruceB · BruceB

Is it possible to purchase a Beta43 without panel and senders, and just purchase the components I need for the panel (buzzer, isolating relay for buzzer, and buttons)? If so, what are the thread specs for the temperature and oil senders. I will be purchasing VDO gauges and senders.

BruceB · BruceB

I am going to be creating a custom engine panel for the Beta43 I will be ordering, and need to mockup the panel for the panel manufacturer. There are two reasons I need a custom panel:The C panel won't fit where my panel goes. It's too wide.I want to add a pyrometer, so need to relayout to accommodate the ad...

krivanj · krivanj

I found some 1/4" pencil zincs that seem to be the same as the Camp E-OBC. I screwed both the original brass zinc from the engine and the new ones into a 1/4" female pipe piece I had, and both seemed to screw in without a problem. Anyone see a problem using these in my engine?

Topic		Started By	Replies	Views	Last Post
	adding a remote tach for a Beta 20 (Preview) I want to install a tach in the **pit of my Vancouver 32. The control panel is below near the nav station, but I want to be able to see the tach when in the **pit - this set-up concept is left over from the original engine (a Bukh 20) and I liked the idea. Has anyone doen this? What is available from Beta for...	CapnB	1	892	Sep 9, 2019 by Farron
	Beta 38 racing full RPMs (Preview) Hi - I have a Beta 38 and the other day it raced to full RPMs at start up. I was able to get it to shut off with the engine panel stop button. I've removed the throttle cover and saw the rack pin on the injector pin was stuck. I was able to get it unstuck. I also removed the stop solenoid and the T shaped bar inside...	captleasure207	1	733	Sep 6, 2019 by Stanley
	Customizing engine panel gauges/senders (Preview) Is it possible to purchase a Beta43 without panel and senders, and just purchase the components I need for the panel (buzzer, isolating relay for buzzer, and buttons)? If so, what are the thread specs for the temperature and oil senders. I will be purchasing VDO gauges and senders.	BruceB	6	939	Aug 30, 2019 by BruceB
	Engine Panel hole specs (Preview) I am going to be creating a custom engine panel for the Beta43 I will be ordering, and need to mockup the panel for the panel manufacturer. There are two reasons I need a custom panel:The C panel won't fit where my panel goes. It's too wide.I want to add a pyrometer, so need to relayout to accommodate the ad...	BruceB	4	781	Aug 26, 2019 by BruceB
	BSP vs NPT thread (Preview) I found some 1/4" pencil zincs that seem to be the same as the Camp E-OBC. I screwed both the original brass zinc from the engine and the new ones into a 1/4" female pipe piece I had, and both seemed to screw in without a problem. Anyone see a problem using these in my engine?	krivanj	4	1195	Aug 24, 2019 by BruceB
«First < 1 … 25 26 27 28 29 … 148 > Last» \| Page of 148 sorted by