Beta Marine Engines

Puffcard · Puffcard

Just starting the install on a Beta 35 with high-rise exhaust, using a Aqualift silencer. Looking at the Beta's Operator's Maintenance Manual, it looks like I only need to add a vent loop / anti-syphon valve if the SW injection point isn't 10" above the water level. Is this correct? I would really lik...

paralog · paralog

Just had a new Beta 25 installed and the rev counter does not return to zero when the engine is off. I am being told this is because it is an electronic gauge. Also the buzzer does not work when the power is turned onto the panel. The panel is the ABVW keyless panel. Is this normal or do I have to go back to the i...

joeb · joeb

I am loosing coolant from my beta 16. I feel like its going into the bilge but i can't find a leak in the hoses anywhere. Yesterday with a cooled engine (I had not run it) i pressure tested the system including the cap. It held 15lbs for 20 minutes. No air leak. Yet after I run her hard, say 2800rpms for 35 m...

mdonnelly · mdonnelly

Had to recently join all the wires in the loom individually as the socket had become badly corroded. One problem since doing this is that the oil pressure gauge is constantly at maximum, even with the engine off. Another problem is that the engine temperature gauge has stopped working. would appreci...

cooper999 · cooper999

Hello Stanley/Farron, We took a trip across the Bay last weekend, with no wind on the return trip, resulting in a 5-hour motor (our first motor this long since we've had the boat). The engine (an older D722) did fine for nearly the entire trip until we were about an hour away from our marina, when it stal...

Topic		Started By	Replies	Views	Last Post
	Exhaust Vented Loop on Beta 35 (Preview) Just starting the install on a Beta 35 with high-rise exhaust, using a Aqualift silencer. Looking at the Beta's Operator's Maintenance Manual, it looks like I only need to add a vent loop / anti-syphon valve if the SW injection point isn't 10" above the water level. Is this correct? I would really lik...	Puffcard	1	917	Oct 10, 2017 by Farron
	Beta 25 new engine installed Rev Counter (Preview) Just had a new Beta 25 installed and the rev counter does not return to zero when the engine is off. I am being told this is because it is an electronic gauge. Also the buzzer does not work when the power is turned onto the panel. The panel is the ABVW keyless panel. Is this normal or do I have to go back to the i...	paralog	2	1180	Sep 30, 2017 by paralog
	Coolant Loss on a Beta 16 (Preview) I am loosing coolant from my beta 16. I feel like its going into the bilge but i can't find a leak in the hoses anywhere. Yesterday with a cooled engine (I had not run it) i pressure tested the system including the cap. It held 15lbs for 20 minutes. No air leak. Yet after I run her hard, say 2800rpms for 35 m...	joeb	2	1232	Sep 20, 2017 by joeb
	Beta 20 wiring loom (Preview) Had to recently join all the wires in the loom individually as the socket had become badly corroded. One problem since doing this is that the oil pressure gauge is constantly at maximum, even with the engine off. Another problem is that the engine temperature gauge has stopped working. would appreci...	mdonnelly	4	1190	Sep 11, 2017 by Farron
	engine stalling in gear (Preview) Hello Stanley/Farron, We took a trip across the Bay last weekend, with no wind on the return trip, resulting in a 5-hour motor (our first motor this long since we've had the boat). The engine (an older D722) did fine for nearly the entire trip until we were about an hour away from our marina, when it stal...	cooper999	7	1561	Sep 9, 2017 by MAP
«First < 1 … 44 45 46 47 48 … 148 > Last» \| Page of 148 sorted by