Beta Marine Engines

NeilMcCubbin · NeilMcCubbin

We have a Beta 60 with nearly 1000 satisfactory hours on it over 3 years use Recently it started misfiring and dying. After some investigation we found that the fuel feed pump was plugged. History is as follows. At initial installation we installed the pump sold by Beta in Norway, since the lift with...

wingsofraven · wingsofraven

Hello Stanley and Farron, We have a newly installed Beta 38 with a tmc 60 transmission. The shaft coupling appears to be a R&D marine split coupling. Would you possibly have the model number of the coupling so I can fabricate a spacer to enable installing shaft spur line cutters? I would like...

steve madden · steve madden

the pump on my beta 50 has developed a leak somewhere back of the impeller housing. the pump to replace per beta marine is a jabsco 29500-1501 which has a 90 degree inlet /outlet which is what I need. the only thing I can find on jabsco web site says this has a 4 inch diameter on the impeller housing and m...

Annie in WA · Annie in WA

We have the our 3-year-old Beta 38 engine pulled right now and while it is out we are planning on opening up, cleaning, and replacing the oil pan gasket as there is some evidence of oil leaking from the flange. The replacement gasket is paper. I've done some research and found differing opinions on ty...

NeilMcCubbin · NeilMcCubbin

The steel covers on the port side engine mounts on our Beta 60 are twisted, for no apparent reason. Refer I have emailed a photo to Stanley because I cannot get one to upload, perhaps because of my poor internet access in the Canary Islands. We just noticed this, although we have run several hundred h...

Topic		Started By	Replies	Views	Last Post
	Which fuel feed pump (Preview) We have a Beta 60 with nearly 1000 satisfactory hours on it over 3 years use Recently it started misfiring and dying. After some investigation we found that the fuel feed pump was plugged. History is as follows. At initial installation we installed the pump sold by Beta in Norway, since the lift with...	NeilMcCubbin	3	1030	Jan 23, 2017 by Stanley
	shaft coupling (Preview) Hello Stanley and Farron, We have a newly installed Beta 38 with a tmc 60 transmission. The shaft coupling appears to be a R&D marine split coupling. Would you possibly have the model number of the coupling so I can fabricate a spacer to enable installing shaft spur line cutters? I would like...	wingsofraven	2	945	Dec 23, 2016 by wingsofraven
	raw water pump replacement (Preview) the pump on my beta 50 has developed a leak somewhere back of the impeller housing. the pump to replace per beta marine is a jabsco 29500-1501 which has a 90 degree inlet /outlet which is what I need. the only thing I can find on jabsco web site says this has a 4 inch diameter on the impeller housing and m...	steve madden	1	885	Dec 8, 2016 by Stanley
	Oil Pan Gasket Replacement (Preview) We have the our 3-year-old Beta 38 engine pulled right now and while it is out we are planning on opening up, cleaning, and replacing the oil pan gasket as there is some evidence of oil leaking from the flange. The replacement gasket is paper. I've done some research and found differing opinions on ty...	Annie in WA	1	795	Nov 28, 2016 by Stanley
	Twisted engine mount cover (Preview) The steel covers on the port side engine mounts on our Beta 60 are twisted, for no apparent reason. Refer I have emailed a photo to Stanley because I cannot get one to upload, perhaps because of my poor internet access in the Canary Islands. We just noticed this, although we have run several hundred h...	NeilMcCubbin	1	736	Nov 8, 2016 by Farron
«First < 1 … 53 54 55 56 57 … 148 > Last» \| Page of 148 sorted by