Beta Marine Engines

mwybo · mwybo

Hi, I have the BD 1005 engine and have been extremely please with performance and support I have received over the last several years. My hi-rise exhaust has cracked in two places near the exhaust manifold connection. I assume that this is due to vibration. My attempts to stabilize the exhaust has not...

redhead 78 · redhead 78

Stanley, I am a happy owner of a 35 beta I installed in my 38 jeanneau gin Fizz 3rd year . My question is I had some fuel issues, I believe because of a original (1977) tank. I had it polished thru the sending unit hole and hope this will take care of it, I plan on cutting a 6" or so inspection plate in the fu...

redhead 78 · redhead 78

Stan, the runaway eng thread remided me of a ? on this subject. Will the electronic stock kill button stop a run away eng issue?? , or would I need to stop it with the stop lever by the throttle linkage? if so I may install a small cable from it with a ring exiting the engine box , rather then have to open...

75c30 · 75c30

Hi, I have a Beta 20 (BD722) and the water pump started leaking. Unfortunately I didn't notice before it was too late and when I removed it, the castings where the studs thread into the front panel broke off and now there's a crack just to the right of where the water pump inserts. Is that front panel avail...

Halfmoon · Halfmoon

Hi Beta 38, 680 engine hours. I recently had a sudden engine stoppage. We had been motoring for about 32 hours non-stop and the engine suddenly died. My first thought was out of fuel, I checked. Tank 1/2 full. Next -I pulled off the bleed screw on the primary filter housing. No fuel visible. No visible...

Topic		Started By	Replies	Views	Last Post
	Hi-rise exhaust - need to replace (Preview) Hi, I have the BD 1005 engine and have been extremely please with performance and support I have received over the last several years. My hi-rise exhaust has cracked in two places near the exhaust manifold connection. I assume that this is due to vibration. My attempts to stabilize the exhaust has not...	mwybo	6	1734	Aug 30, 2013 by Stanley
	fuel filters (Preview) Stanley, I am a happy owner of a 35 beta I installed in my 38 jeanneau gin Fizz 3rd year . My question is I had some fuel issues, I believe because of a original (1977) tank. I had it polished thru the sending unit hole and hope this will take care of it, I plan on cutting a 6" or so inspection plate in the fu...	redhead 78	1	960	Aug 15, 2013 by Stanley
	run away eng (Preview) Stan, the runaway eng thread remided me of a ? on this subject. Will the electronic stock kill button stop a run away eng issue?? , or would I need to stop it with the stop lever by the throttle linkage? if so I may install a small cable from it with a ring exiting the engine box , rather then have to open...	redhead 78	1	572	Aug 15, 2013 by Stanley
	Corosion near the water pump (Preview) Hi, I have a Beta 20 (BD722) and the water pump started leaking. Unfortunately I didn't notice before it was too late and when I removed it, the castings where the studs thread into the front panel broke off and now there's a crack just to the right of where the water pump inserts. Is that front panel avail...	75c30	2	504	Aug 10, 2013 by 75c30
	BETA 38 Lift pump problem (Preview) Hi Beta 38, 680 engine hours. I recently had a sudden engine stoppage. We had been motoring for about 32 hours non-stop and the engine suddenly died. My first thought was out of fuel, I checked. Tank 1/2 full. Next -I pulled off the bleed screw on the primary filter housing. No fuel visible. No visible...	Halfmoon	5	2662	Aug 5, 2013 by Halfmoon
«First < 1 … 77 78 79 80 81 … 147 > Last» \| Page of 147 sorted by