Beta Marine Engines

bosunj · bosunj

While looking over the job of installing the panel to finally get this engine ready to go I noticed there is no wire present that attaches to the oil pressure sensor. I am unable to find anything about it in the manual. Please provide guidance. Thank you.

egantsea · egantsea

Hi, We have a 38 hp Beta in our 36sail boat. At 250 hours maintenance it is secluded that we clean the heat exchanger tube stack. We did the process and got it all back together and it leaks from both ends. We lined up the slot on the front side, tightened the back bolt down about 80% then the forward one about...

Zoe · Zoe

I have a Beta 60 with ZF 45-C Gearbox on order which I will be connecting to my existing Walter V-Drive and LH Propeller. Am I right in assuming the LH propeller rotation is the correct one for this combination. Not the sort of mistake you want to find out when leaving the dock for the first time! Thanks, Zo...

tribute · tribute

I have had intermittent issues with my alternator (standard) on my 2006 1005 over the last few years. I had it bench tested and all was well so it was the connections. It works 95% of the time despite my best efforts to keep the connections clean and well tightened Early this season there was a short on o...

Gordon · Gordon

Glad I found this site. I'm in the throes of making a final decision about replacing a 2gm20 that has exhausted my patience. The boat is 33ft overall, 26ft waterline and weighs about 9500 lbs dry. I'm guessing the cruising weight of the boat (full fuel and water, normal cruising equipment and stores)...

Topic		Started By	Replies	Views	Last Post
	Beta20 oil pressure sensor wire (Preview) While looking over the job of installing the panel to finally get this engine ready to go I noticed there is no wire present that attaches to the oil pressure sensor. I am unable to find anything about it in the manual. Please provide guidance. Thank you.	bosunj	2	781	Feb 19, 2013 by bosunj
	heat exchanger tube stack leaking after cleaning (Preview) Hi, We have a 38 hp Beta in our 36sail boat. At 250 hours maintenance it is secluded that we clean the heat exchanger tube stack. We did the process and got it all back together and it leaks from both ends. We lined up the slot on the front side, tightened the back bolt down about 80% then the forward one about...	egantsea	5	11125	Feb 16, 2013 by egantsea
	PROPELLER ROTATION (Preview) I have a Beta 60 with ZF 45-C Gearbox on order which I will be connecting to my existing Walter V-Drive and LH Propeller. Am I right in assuming the LH propeller rotation is the correct one for this combination. Not the sort of mistake you want to find out when leaving the dock for the first time! Thanks, Zo...	Zoe	5	4174	Feb 4, 2013 by Annie in WA
	Electrical issues (Preview) I have had intermittent issues with my alternator (standard) on my 2006 1005 over the last few years. I had it bench tested and all was well so it was the connections. It works 95% of the time despite my best efforts to keep the connections clean and well tightened Early this season there was a short on o...	tribute	6	1102	Dec 31, 2012 by Stanley
	Yanmar 2GM20F replacement (Preview) Glad I found this site. I'm in the throes of making a final decision about replacing a 2gm20 that has exhausted my patience. The boat is 33ft overall, 26ft waterline and weighs about 9500 lbs dry. I'm guessing the cruising weight of the boat (full fuel and water, normal cruising equipment and stores)...	Gordon	2	4435	Dec 19, 2012 by Farron
«First < 1 … 83 84 85 86 87 … 148 > Last» \| Page of 148 sorted by