Beta Marine Engines

danjcon · danjcon

I talked with Farron last week about a problem I was having where my 2008 Beta 16 would start up fine, but when I tried to put it into gear it would stall. He sugegsted after our discussion that my throttle mechanism was probably causing a problem with revving the engine before getting fully into gear. I...

seators · seators

new install of a Beta 16 on my Tartan 30. Feel like i have a pretty good alignment. Have two problems: 1. only getting 3000 rpm in WOT. shaft spins freely by hand. top speed of 5.2 knots. 2. VERY small amount of transmission fluid leaking from behind output flange of transmission. Just enough to w...

Snufle · Snufle

Hi guys, I just thought I'd try asking for help on this forum, as I'm a bit of a novice on engines and have a Beta Marine 14 that won't fire up: The engine died on me on my way into the harbour a couple of weeks back. I noticed the idle was a bit low, and when I tried to increase throttle the rpms didn't increase. I...

Wolf Hound · Wolf Hound

We have a new (to us) boat, re-powered with a Beta 35 engine, which I like very well so far. It's of course a good idea to get better acquainted with the engine, so, when I'm not at the boat (which is about three hours away from our house) I'd like to read through the engine manual. We do have a manual on boa...

Brendan · Brendan

I have overheating problems with my beta 10 . After overheating some gunk appeared in the heat exchanger where you top up the coolant! When idling it will shift 6 litres of seawater/min. but when revved up this does not increase much if at all I have checked the impeller, it's ok I have replaced the therm...

Topic		Started By	Replies	Views	Last Post
	Beta 16 problem (Preview) I talked with Farron last week about a problem I was having where my 2008 Beta 16 would start up fine, but when I tried to put it into gear it would stall. He sugegsted after our discussion that my throttle mechanism was probably causing a problem with revving the engine before getting fully into gear. I...	danjcon	1	993	Sep 26, 2012 by Stanley
	fluid from TMC 40 output flange on Beta 16 installation into Tartan 30 (Preview) new install of a Beta 16 on my Tartan 30. Feel like i have a pretty good alignment. Have two problems: 1. only getting 3000 rpm in WOT. shaft spins freely by hand. top speed of 5.2 knots. 2. VERY small amount of transmission fluid leaking from behind output flange of transmission. Just enough to w...	seators	4	1532	Sep 23, 2012 by seators
	Beta 14 won't start (Preview) Hi guys, I just thought I'd try asking for help on this forum, as I'm a bit of a novice on engines and have a Beta Marine 14 that won't fire up: The engine died on me on my way into the harbour a couple of weeks back. I noticed the idle was a bit low, and when I tried to increase throttle the rpms didn't increase. I...	Snufle	3	2100	Sep 18, 2012 by Stanley
	Beta Manuals Online (Preview) We have a new (to us) boat, re-powered with a Beta 35 engine, which I like very well so far. It's of course a good idea to get better acquainted with the engine, so, when I'm not at the boat (which is about three hours away from our house) I'd like to read through the engine manual. We do have a manual on boa...	Wolf Hound	2	793	Sep 17, 2012 by Wolf Hound
	Overheating (Preview) I have overheating problems with my beta 10 . After overheating some gunk appeared in the heat exchanger where you top up the coolant! When idling it will shift 6 litres of seawater/min. but when revved up this does not increase much if at all I have checked the impeller, it's ok I have replaced the therm...	Brendan	5	2299	Sep 13, 2012 by Brendan
«First < 1 … 86 87 88 89 90 … 148 > Last» \| Page of 148 sorted by