Beta Marine Engines

scottmcg · scottmcg

Dear Stanley,I am replacing the Yanmar YSB-12 this spring in my 1977 S2 9.2A (aft ****pit). The Beta BD902 (25hp) looks good as a replacement based on information on this board and the Betamarine websites. We have large tidal currents here in the San Juans and British Columbia (usually when going d...

Christiang · Christiang

HI Stanley I have an old Beta 13.5. I tried to replace the gasket on the exhaust elbow and found that it had ben fitted with helicoils as the bolt holes had corroded somewhat. Please refer to image attached. 2 of the helicoils have since failed and I had to remove them. Can you suggest a next step. Should I r...

armatore34 · armatore34

i wonder if the flexible mounting for the beta on a working boat could be done RIGID as pumps would be connected to the engine ... The angle the engine prop to enginge could work would be around 4 degree and so as low as possible... I wonder if the beta 90 or 105 would accept these mounting and if t...

arjan · arjan

Since I have been getting fantastic support through the forums I would like to ask another question. I have two ABV panels with the VDO tachs that have build in digital hour meters. The panels are under a hard dodger and fairly well protected from the elements but do get wet sometimes when washing the bo...

bdwyer · bdwyer

I put a new oil pad under my 2005 1005 with 200 hours on it after winterization. Today I noticed a fair amount of fuel on the pad and while I could not find the source of the leak there was some fuel pooled at the top of the engine at the three points were the fuel enters the cylinders. Nothing seemed wrong so I...

Topic		Started By	Replies	Views	Last Post
	Beta 902 install in S2 9.2a (Preview) Dear Stanley,I am replacing the Yanmar YSB-12 this spring in my 1977 S2 9.2A (aft ****pit). The Beta BD902 (25hp) looks good as a replacement based on information on this board and the Betamarine websites. We have large tidal currents here in the San Juans and British Columbia (usually when going d...	scottmcg	2	1729	Apr 14, 2011 by Stanley
	BZ482 heat exchange tank (Preview) HI Stanley I have an old Beta 13.5. I tried to replace the gasket on the exhaust elbow and found that it had ben fitted with helicoils as the bolt holes had corroded somewhat. Please refer to image attached. 2 of the helicoils have since failed and I had to remove them. Can you suggest a next step. Should I r...	Christiang	2	1249	Apr 12, 2011 by Christiang
	mountig of beta marine (Preview) i wonder if the flexible mounting for the beta on a working boat could be done RIGID as pumps would be connected to the engine ... The angle the engine prop to enginge could work would be around 4 degree and so as low as possible... I wonder if the beta 90 or 105 would accept these mounting and if t...	armatore34	1	1091	Mar 23, 2011 by Stanley
	hour meter problems (Preview) Since I have been getting fantastic support through the forums I would like to ask another question. I have two ABV panels with the VDO tachs that have build in digital hour meters. The panels are under a hard dodger and fairly well protected from the elements but do get wet sometimes when washing the bo...	arjan	4	4159	Mar 14, 2011 by arjan
	Fuel Leak (Preview) I put a new oil pad under my 2005 1005 with 200 hours on it after winterization. Today I noticed a fair amount of fuel on the pad and while I could not find the source of the leak there was some fuel pooled at the top of the engine at the three points were the fuel enters the cylinders. Nothing seemed wrong so I...	bdwyer	3	1062	Mar 8, 2011 by Stanley
«First < 1 … 104 105 106 107 108 … 148 > Last» \| Page of 148 sorted by