Beta Marine Engines

moliddy · moliddy

Stanley, I want to winterize my Beta BD1005 myself...I've changed the oil and filter...I have the manual about closing the raw water sea**** and placing the intake hose into a bucket of pink antifreeze...letting the engine run until the pink stuff starts to exit the exhaust... My question is about t...

Bombay77 · Bombay77

I have a 25 hp BETA (BD902EPA) and would like to get the fittings for the jacket water to heat the cabin and hot water tank while the engine is running. How difficult is it to do this and where do the fittings go on the engine?

Chris · Chris

Im in the process of installing a new Beta 28 in my 1965 Allied Seabreeze. I'm replacing the existing tank, but plan on keeping the same location which is aft of the engine (secured under the ****pits deck) and above it (top of the tank ~10-12 above engine). Will this present any unique problems sin...

mikeB · mikeB

I have noticed a very small leak around my engine zinc.The only evidence was was a bit of barely noticeable steam while I was running the engine at the dock after a month of remaining idle. I recently replaced the zinc and tightened it as much as I could.Can I use teflon tape around the threads to help seal...

Chris · Chris

Im in the process of installing a new Beta 28 in my 1965 Allied Seabreeze. The engine manual states the raw water intake needs to be 1 dia. Minimum. The boats old Atomic 4 inlet is ~1/2 diameter. I noticed the engines inlet pipe for the raw water pump is ½. My question is since the inlet on the engine is...

Topic		Started By	Replies	Views	Last Post
	Winterizing the BD1005 (Preview) Stanley, I want to winterize my Beta BD1005 myself...I've changed the oil and filter...I have the manual about closing the raw water sea**** and placing the intake hose into a bucket of pink antifreeze...letting the engine run until the pink stuff starts to exit the exhaust... My question is about t...	moliddy	2	992	Dec 14, 2009 by moliddy
	Jacket water fittings for Red Dot and hot water tank (Preview) I have a 25 hp BETA (BD902EPA) and would like to get the fittings for the jacket water to heat the cabin and hot water tank while the engine is running. How difficult is it to do this and where do the fittings go on the engine?	Bombay77	1	1179	Dec 11, 2009 by Stanley
	Possible issues of a fuel tank located higher than the engine? (Preview) Im in the process of installing a new Beta 28 in my 1965 Allied Seabreeze. I'm replacing the existing tank, but plan on keeping the same location which is aft of the engine (secured under the ****pits deck) and above it (top of the tank ~10-12 above engine). Will this present any unique problems sin...	Chris	1	1091	Dec 7, 2009 by Stanley
	Weeping around zinc. (Preview) I have noticed a very small leak around my engine zinc.The only evidence was was a bit of barely noticeable steam while I was running the engine at the dock after a month of remaining idle. I recently replaced the zinc and tightened it as much as I could.Can I use teflon tape around the threads to help seal...	mikeB	2	901	Nov 23, 2009 by mikeB
	Beta 28hp - Min diameter water inlet (Preview) Im in the process of installing a new Beta 28 in my 1965 Allied Seabreeze. The engine manual states the raw water intake needs to be 1 dia. Minimum. The boats old Atomic 4 inlet is ~1/2 diameter. I noticed the engines inlet pipe for the raw water pump is ½. My question is since the inlet on the engine is...	Chris	2	1282	Nov 18, 2009 by Chris
«First < 1 … 117 118 119 120 121 … 148 > Last» \| Page of 148 sorted by