Beta Marine Engines

SkipD · SkipD

This is a 2019 installation in an Albin 27 with a Beta 50 w/TMC60 and Python-Drive, less than a 100 hours to date. Overall everything is working fine. Have always been sensitive to noise and have insulated & reinforced the boat to get the noise level down to 76db at 2000 rpm just above the engine com...

Johan W · Johan W

Hi, I have a 10 year old BD722, 20hp engine Installed in my sailing boat. The sea water pump is leaking water from the backside. I have ordered a new original spare part pump. My questions are, do I need any special tools to remove the old one and install the new one or is it just to loosen the two screws/clam...

hkbrad · hkbrad

good day all, I am new to the forum having stumbled across it in my quest to sort an ongoing issue with my Beta BZ482G engine.It is used to spin a meecealte generator on a sailboat. Engine appears to be running quite well after I have recently removed it, cleaned it up, replaced exhaust elbow and all filte...

BruceB · BruceB

For the life of me I can't stop a leak in the 7/8" raw water hose that attaches to the back of the heat exchanger of my Beta43. I've tightened the hose clamp as tight as I can get it and it is still leaking. I'm going to take the hose off and see if there is a defect in the hose. Is this hose a stock item?

Mitch Brown · Mitch Brown

I bought a 1973 Tartan T30c. The PO installed the motor poorly. As a result, the mounts are all twisted and need to be replaced (2 might be salvageable). The forward, starboard cast-iron "flange" holding the motor mount broke completely away. Cast iron can't be welded. There are some holes that look l...

Topic		Started By	Replies	Views	Last Post
	TMC60- Clicking/Ticking Noise (Preview) This is a 2019 installation in an Albin 27 with a Beta 50 w/TMC60 and Python-Drive, less than a 100 hours to date. Overall everything is working fine. Have always been sensitive to noise and have insulated & reinforced the boat to get the noise level down to 76db at 2000 rpm just above the engine com...	SkipD	7	704	Aug 10, 2020 by Stanley
	Replacement of the sea water pump (Preview) Hi, I have a 10 year old BD722, 20hp engine Installed in my sailing boat. The sea water pump is leaking water from the backside. I have ordered a new original spare part pump. My questions are, do I need any special tools to remove the old one and install the new one or is it just to loosen the two screws/clam...	Johan W	1	754	Aug 6, 2020 by Stanley
	BZ482 Fuel solenoid cutting out engine (Preview) good day all, I am new to the forum having stumbled across it in my quest to sort an ongoing issue with my Beta BZ482G engine.It is used to spin a meecealte generator on a sailboat. Engine appears to be running quite well after I have recently removed it, cleaned it up, replaced exhaust elbow and all filte...	hkbrad	2	716	Aug 3, 2020 by hkbrad
	7/8" raw water hose to heat exchanger leaking (Preview) For the life of me I can't stop a leak in the 7/8" raw water hose that attaches to the back of the heat exchanger of my Beta43. I've tightened the hose clamp as tight as I can get it and it is still leaking. I'm going to take the hose off and see if there is a defect in the hose. Is this hose a stock item?	BruceB	12	1048	Aug 1, 2020 by BruceB
	2015 Beta 16 in 1973 Tartan T30c - broken stbd. fwd. motor mount "flange" (Preview) I bought a 1973 Tartan T30c. The PO installed the motor poorly. As a result, the mounts are all twisted and need to be replaced (2 might be salvageable). The forward, starboard cast-iron "flange" holding the motor mount broke completely away. Cast iron can't be welded. There are some holes that look l...	Mitch Brown	1	519	Jul 22, 2020 by Stanley
«First < 1 … 16 17 18 19 20 … 148 > Last» \| Page of 148 sorted by