Beta Marine Engines

Opie91 · Opie91

Hi, I saw another thread about adding an external regulator on a 75 amp ISKRA alternator. It was said that any alternator shop could make the necessary modifications . Would this also apply to a Beta 20 early model with the 70 amp ISKRA? Will the Balmar unit work with this model also? Same type modifi...

Islander · Islander

A few details about my installation: The Beta 16 was installed new in the summer of 2009 replacing a Volvo MD7A. The engine has a high-rise exhaust and I used the same waterlock muffler as was installed on the Volvo. In addition I used the same 3/4" Marelon Sea**** that was original to the boat, and ...

rleporati · rleporati

I pulled and cleaned my Beta 25 heat exchanger tubes and reinstalled with new O rings but have a persistent leak at the front end. Tried tightening the three hex bolts but no luck. Permatex gasket ???

BillConber · BillConber

I have a new Beta 38 with a keyless (CW) panel. I have a 120 amp alternator with an external regulator and a Blue Sea ACR. Two battery banks: a start battery and 4 house batteries. I want to isolate the start battery from the engine (per manual instruction) and depower the panel when I am away from the boat....

Court · Court

Corrosion has caused the paint to flake off around the base of my raw water pump. There is no apparent leak and the impeller and top seal are in good condition, I don't know how the shaft is sealed. My zinc was almost totally dissolved. Is this just galvanic corrosion and I need to change the zinc more freq...

Topic		Started By	Replies	Views	Last Post
	Beta 20 External Regulator (Preview) Hi, I saw another thread about adding an external regulator on a 75 amp ISKRA alternator. It was said that any alternator shop could make the necessary modifications . Would this also apply to a Beta 20 early model with the 70 amp ISKRA? Will the Balmar unit work with this model also? Same type modifi...	Opie91	9	1282	Apr 30, 2018 by Stanley
	Beta 16 - Low Power and Overheating (Preview) A few details about my installation: The Beta 16 was installed new in the summer of 2009 replacing a Volvo MD7A. The engine has a high-rise exhaust and I used the same waterlock muffler as was installed on the Volvo. In addition I used the same 3/4" Marelon Sea**** that was original to the boat, and ...	Islander	14	1390	Apr 26, 2018 by Islander
	Heat exchanger Gaskets ??? (Preview) I pulled and cleaned my Beta 25 heat exchanger tubes and reinstalled with new O rings but have a persistent leak at the front end. Tried tightening the three hex bolts but no luck. Permatex gasket ???	rleporati	4	659	Mar 20, 2018 by rleporati
	Isolate start battery (Preview) I have a new Beta 38 with a keyless (CW) panel. I have a 120 amp alternator with an external regulator and a Blue Sea ACR. Two battery banks: a start battery and 4 house batteries. I want to isolate the start battery from the engine (per manual instruction) and depower the panel when I am away from the boat....	BillConber	1	654	Mar 19, 2018 by Stanley
	Raw Water pump corrosion (Preview) Corrosion has caused the paint to flake off around the base of my raw water pump. There is no apparent leak and the impeller and top seal are in good condition, I don't know how the shaft is sealed. My zinc was almost totally dissolved. Is this just galvanic corrosion and I need to change the zinc more freq...	Court	5	1108	Mar 2, 2018 by Stanley
«First < 1 … 39 40 41 42 43 … 148 > Last» \| Page of 148 sorted by