Beta Marine Engines

StuartWeibel · StuartWeibel

I'm commissioning my Beta 14 and have not been able to get the engine above 2750 RPM. Raw water supply is 19 mm, functioning well, no signs of overheating (temp gauge ~60) The engine runs up to 3700 RPM under no load (suggesting the engine and Tachometer are functioning properly over all. The logical ca...

CapnB · CapnB

I am installing a Beta 20 in a Vancouver 32 sailboat. Beta Marine indicates that the water strainer for the seawater inlet should be mounted above the waterline. My previous engines have all had the strainer mounted below the waterline, near the sea****. Is this a problem? Can someone explain the pro...

StuartWeibel · StuartWeibel

The accompanying picture shows the point of attachment of the water pump on my new B-14. It appears to me that there is a missing clamp. There are two holding the base of the pump to the engine block, and a post that would seem to be in a position to attach a third hold-down clip. Can you confirm for me tha...

StuartWeibel · StuartWeibel

http://betamarine.co.uk/wp-content/uploads/downloads/seagoing_guidelines/beta10_and_beta14_he_drawings/Beta-14-HE-TMC40...

Gordan · Gordan

I have purchase a Beta system with Dual helms, one with deluxe C panel and the other helm using the new D panel. I have installed both panels and used the provided wire harness. After engine starts all warning lights go off, tach, temp and volts gauges are working however the C Panel only has a continuou...

Topic		Started By	Replies	Views	Last Post
	Commissioning a Beta 14: engine won't run beyond 2700 RPM under load propeller sizing RPM limiting factors commissioning tests (Preview) I'm commissioning my Beta 14 and have not been able to get the engine above 2750 RPM. Raw water supply is 19 mm, functioning well, no signs of overheating (temp gauge ~60) The engine runs up to 3700 RPM under no load (suggesting the engine and Tachometer are functioning properly over all. The logical ca...	StuartWeibel	7	1353	Aug 23, 2017 by StuartWeibel
	water strainer mounted above waterline? (Preview) I am installing a Beta 20 in a Vancouver 32 sailboat. Beta Marine indicates that the water strainer for the seawater inlet should be mounted above the waterline. My previous engines have all had the strainer mounted below the waterline, near the sea****. Is this a problem? Can someone explain the pro...	CapnB	1	797	Aug 14, 2017 by Stanley
	Water pump attachment on Beta Marine 14 (Preview) The accompanying picture shows the point of attachment of the water pump on my new B-14. It appears to me that there is a missing clamp. There are two holding the base of the pump to the engine block, and a post that would seem to be in a position to attach a third hold-down clip. Can you confirm for me tha...	StuartWeibel	1	486	Jul 17, 2017 by Stanley
	Engineering diagram discrepancy? (Preview) http://betamarine.co.uk/wp-content/uploads/downloads/seagoing_guidelines/beta10_and_beta14_he_drawings/Beta-14-HE-TMC40...	StuartWeibel	1	506	Jul 10, 2017 by Stanley
	C Panel Alarm Buzzer continous (Preview) I have purchase a Beta system with Dual helms, one with deluxe C panel and the other helm using the new D panel. I have installed both panels and used the provided wire harness. After engine starts all warning lights go off, tach, temp and volts gauges are working however the C Panel only has a continuou...	Gordan	6	1788	Jul 5, 2017 by Gordan
«First < 1 … 45 46 47 48 49 … 148 > Last» \| Page of 148 sorted by