Beta Marine Engines

jyoors · jyoors

I have a new beta 25 with the 75 amp alternator. What voltage should this alternator put out at idle?

egantsea · egantsea

Hi, We are not able to start our Beta 38 hp motor with two alternators. When the key turns to "Start" the engine does nothing - no clicking, no starter noise. It was running just fine as we were in the process of changing the oil and filter. We ran the motor to heat up the oil then turned it off to p...

Spottydog · Spottydog

I am replacing the heat exchanger on my 2006 Beta 14 due to corrosion on the lip seal. I have received a new extruded unit with new gaskets. The gasket set consists of 2 alu spacers 2 material gaskets and 1 metal gasket that links the 2 ports. Can you advise me of the fitting sequence of these gaskets please...

ssfein · ssfein

I am replacing a westerbeke 33 on a Sabre 38 mk 1. lwl 31.5 , dis 15500 , beam 11.5 . So far the Beta recomindations have been for a 30 or 35. If at all possable I would like to save my Campbell prop which is a rh 15x 8 with cupped blades. hull speed is calc at 7.5 thanks

BobC · BobC

I have a Beta 25 with the tmc40 transmission. Over the past summer, I have noticed a leak from the rear seal of the engine. It is only a drop or two when cruising at above 2000 rpm for several hours or more. I have monitored/adjusted the fluid level between the upper and lower dipstick marks (measured when...

Topic		Started By	Replies	Views	Last Post
	Charging question beta 25 25 charge (Preview) I have a new beta 25 with the 75 amp alternator. What voltage should this alternator put out at idle?	jyoors	1	599	Dec 30, 2014 by Stanley
	Wont start! (Preview) Hi, We are not able to start our Beta 38 hp motor with two alternators. When the key turns to "Start" the engine does nothing - no clicking, no starter noise. It was running just fine as we were in the process of changing the oil and filter. We ran the motor to heat up the oil then turned it off to p...	egantsea	3	1479	Nov 17, 2014 by Stanley
	Replacement Heat Exchanger for Beta 14 (Preview) I am replacing the heat exchanger on my 2006 Beta 14 due to corrosion on the lip seal. I have received a new extruded unit with new gaskets. The gasket set consists of 2 alu spacers 2 material gaskets and 1 metal gasket that links the 2 ports. Can you advise me of the fitting sequence of these gaskets please...	Spottydog	3	942	Nov 7, 2014 by Farron
	repower (Preview) I am replacing a westerbeke 33 on a Sabre 38 mk 1. lwl 31.5 , dis 15500 , beam 11.5 . So far the Beta recomindations have been for a 30 or 35. If at all possable I would like to save my Campbell prop which is a rh 15x 8 with cupped blades. hull speed is calc at 7.5 thanks	ssfein	1	591	Oct 14, 2014 by Farron
	tmc40 transmission rear seal leak (Preview) I have a Beta 25 with the tmc40 transmission. Over the past summer, I have noticed a leak from the rear seal of the engine. It is only a drop or two when cruising at above 2000 rpm for several hours or more. I have monitored/adjusted the fluid level between the upper and lower dipstick marks (measured when...	BobC	1	855	Sep 22, 2014 by Stanley
«First < 1 … 69 70 71 72 73 … 147 > Last» \| Page of 147 sorted by