Beta Marine Engines

James Bibb · James Bibb

Trying to re-use exisitng shaft in good condition, I mounted my new Beta 482 shaft/propeller assembly too tight so that the propellor hub is rubbing against the strut in exceleration conditions....I don't have the 1/2" min space recommended between the propellor and rear portion the strut,...

bhouck · bhouck

I have the B1005 Beta engine. Installed it 5 years ago and it has been great. My battery bank has a starter battery and 2 house banks. One deep cycle and 2 6volt in parallel. These run through a battery isolator, which is no longer working. I need to replace the isolator and have run into a question. Does th...

alteredcourse30 · alteredcourse30

Hi Stanley, I have the beta20, with the water lift muffler that is too small as noted by yourself and Beta uk - in relation to the trouble I had with the high pressure fuel pump....The boat is a Catalina30 with the new 2" exhaust routed up into the kitchen cabinet, behind the sink and out along the po...

egantsea · egantsea

Hi, We have two 100 amp alternators on our Beta 38 hp engine. We are setting up a battery monitor system and need to know the grounding method of the alternators. These are factory installed alternators. Are these alternator case grounded to the engine block? Thank you, Chip -- Edited by egantsea on F...

Jetexas · Jetexas

I installed a BZ482 in my Starwind 27. The engine runs great, but the belt is rubbing on both the cooling hose that runs under the alternator and against the flange where the oil filter screws on. Are there pulley spacers available to move the belt out a little more?

Topic		Started By	Replies	Views	Last Post
	Coupling Spacer Proposal (Preview) Trying to re-use exisitng shaft in good condition, I mounted my new Beta 482 shaft/propeller assembly too tight so that the propellor hub is rubbing against the strut in exceleration conditions....I don't have the 1/2" min space recommended between the propellor and rear portion the strut,...	James Bibb	2	841	May 30, 2012 by Stanley
	Battery Isolator (Preview) I have the B1005 Beta engine. Installed it 5 years ago and it has been great. My battery bank has a starter battery and 2 house banks. One deep cycle and 2 6volt in parallel. These run through a battery isolator, which is no longer working. I need to replace the isolator and have run into a question. Does th...	bhouck	1	643	May 29, 2012 by Stanley
	water lift muffler sizing. (Preview) Hi Stanley, I have the beta20, with the water lift muffler that is too small as noted by yourself and Beta uk - in relation to the trouble I had with the high pressure fuel pump....The boat is a Catalina30 with the new 2" exhaust routed up into the kitchen cabinet, behind the sink and out along the po...	alteredcourse30	11	5341	May 24, 2012 by Farron
	Are these alternators case grounded? (Preview) Hi, We have two 100 amp alternators on our Beta 38 hp engine. We are setting up a battery monitor system and need to know the grounding method of the alternators. These are factory installed alternators. Are these alternator case grounded to the engine block? Thank you, Chip -- Edited by egantsea on F...	egantsea	1	787	May 11, 2012 by Stanley
	Belt rubbing on Z482 (Preview) I installed a BZ482 in my Starwind 27. The engine runs great, but the belt is rubbing on both the cooling hose that runs under the alternator and against the flange where the oil filter screws on. Are there pulley spacers available to move the belt out a little more?	Jetexas	5	1316	May 1, 2012 by Jetexas
«First < 1 … 90 91 92 93 94 … 148 > Last» \| Page of 148 sorted by