Beta Marine Engines

cooper999 · cooper999

I feel like I'm always the one to ask the stupid question, but so be it I have an older D722, serial # 545598. I have a manual I downloaded for the D722, but it's apparent that the model featured is well newer than my motor. I'm unclear as to how to drain the coolant-I'd like to inspect the heat exchanger befo...

massimo45 · massimo45

Dear Mr. Stanley, I re-engined my Alpa38, 11 tons, 9 mt waterline that was equipped with a Perkins 4.108, inverter Hurt 250, with a BETA 60, TMC260 inverter with 2: 1 ratio, that will be delivered to me in late February. I ask you if I can continue to use my existing propeller, a Max Prop three blades 18 ', a...

genkinyc · genkinyc

Hi. I have a 1 5/8 output from my Beta 20 - Hi Rise exhaust output that will run to a new water lift muffler. I have approx 10ft run of 1 7/8 exhaust hose running upwards to a high loop and down to the transom exit point. I found the Centek Vernalift 1.63 X 1.88 Vernalift (Top In) 8 X 8 which will fit the hoses perf...

Jok · Jok

I am planning to repower a Halberg-rassy Rasmus 35. The original engine was a Volvo MD21B (75HP), I am thinking of going with ether the Beta 43 or Beta 38. The boat has a 27.58 LWL, 10" beam, and a 12100lbs displacement Here is the link to the specs on Sailboat Data. http://sailboatdata.com/viewrecor...

egantsea · egantsea

Hi, We removed the bracket we had asked you about. While removing the bracket we noticed a split hose that goes into the impeller housing. It was leaking slightly. We removed the hose and cut an inch or so off it. Then connected it again and used a new hose clamp. There was one hose clamp on it originally...

Topic		Started By	Replies	Views	Last Post
	draining coolant on older D722 (Preview) I feel like I'm always the one to ask the stupid question, but so be it I have an older D722, serial # 545598. I have a manual I downloaded for the D722, but it's apparent that the model featured is well newer than my motor. I'm unclear as to how to drain the coolant-I'd like to inspect the heat exchanger befo...	cooper999	4	665	Feb 22, 2017 by cooper999
	Max Prop 18' for a Beta 60 ? (Preview) Dear Mr. Stanley, I re-engined my Alpa38, 11 tons, 9 mt waterline that was equipped with a Perkins 4.108, inverter Hurt 250, with a BETA 60, TMC260 inverter with 2: 1 ratio, that will be delivered to me in late February. I ask you if I can continue to use my existing propeller, a Max Prop three blades 18 ', a...	massimo45	2	518	Feb 20, 2017 by massimo45
	Beta 20 - Exhaust Water Lift Muffler Sizing ? (Preview) Hi. I have a 1 5/8 output from my Beta 20 - Hi Rise exhaust output that will run to a new water lift muffler. I have approx 10ft run of 1 7/8 exhaust hose running upwards to a high loop and down to the transom exit point. I found the Centek Vernalift 1.63 X 1.88 Vernalift (Top In) 8 X 8 which will fit the hoses perf...	genkinyc	3	2830	Feb 16, 2017 by Stanley
	Repower a Hallberg-rassy Rasmus 35 (Preview) I am planning to repower a Halberg-rassy Rasmus 35. The original engine was a Volvo MD21B (75HP), I am thinking of going with ether the Beta 43 or Beta 38. The boat has a 27.58 LWL, 10" beam, and a 12100lbs displacement Here is the link to the specs on Sailboat Data. http://sailboatdata.com/viewrecor...	Jok	2	2216	Feb 10, 2017 by Jok
	Leaking hose to impeller housing (Preview) Hi, We removed the bracket we had asked you about. While removing the bracket we noticed a split hose that goes into the impeller housing. It was leaking slightly. We removed the hose and cut an inch or so off it. Then connected it again and used a new hose clamp. There was one hose clamp on it originally...	egantsea	1	829	Feb 9, 2017 by Farron
«First < 1 … 50 51 52 53 54 … 148 > Last» \| Page of 148 sorted by